Handheld broaches specially designed used to clean epoxy buildup from the inside of lamination tooling slots and holes.
|Cleaning broaches||Part number|
|.1875" x .2500" slot||OP-39-2518-10-0001|
|Replacement inserts||Part number|
|.1875" x .2500" slot||OP-39-2518-30-0001|
|Broach handles||Part number|
|Slotted & .2500" round||OP-39-0250-30-0004|
Additional sizes or special requirements available upon request.
Twisted in wire, all stainless steel tube brushes are used for cleaning slotted and round holes in your separator plates. Choose from two styles of handles depending on your personal preference.
|S.S. tube brushes with 1/4" eyelet||Part number|
|S.S. tube brushes with straight shank||Part number|
|Brush handles||Part number|
|Handle w/locking collet (use with straight shank brushes)||OP-40-4000-30-0001|
|T handle style (use with 1/4" eyelet brushes)||OP-40-0750-30-0001|
Hand pads for polishing & cleaning your lamination components and fixtures. These pads are offered in three levels of aggresiveness for mild to difficult plate cleaning operations.
- Heavy Duty - For scratch removal and heavy epoxy deposits.
- Medium Duty - For light scratch removal, light epoxy deposits and blending heavy duty scratches.
- Light Duty - For finishing and final blending.
The cleaning pads are offered in a convenient pre-cut size (3" x 4 1/2") to fit our durable hand held pad holder, also offered. The pad holder provides increased leverage and prevents pressure points caused by hand sanding, giving a more consistent and even finish to your plates.
|Buld pack / Pre-cut pads||Part number|
|Heavy duty pads - 20 / case||OP-40-0304-30-0004|
|Medium duty pads - 20 / case||OP-40-0304-30-0005|
|Light duty pads - 20 / case||OP-40-0304-30-0006|
|One pad holder||Part number|
|One - 3 ¼" x 4 ¾" pad holder||OP-40-0304-30-0011|
Heavy duty vibratory finishing bowl used to automatically remove epoxy build up from your lamination pins. This system will effectively clean and polish the pins without risk of causing damage.
Use the optional flow through rinsing system and save on labor by delivering cleaner, brighter pins. The rinsing system also helps to maximize life of the polishing media. For best results use the concentrate rinse additive, dilution 2% in water.
C.A.PICARD® recommends using the optional screening kit to aid in the separation of your pins from the cleaning media. Also useful for separating undersize media from usable media. Screen kit includes the following: One 1/4" Screen plus a 1 cu. ft. tote contain
|Pin cleaning equipment||Part number|
|Vibratory bowl (110V 60Hz)||OP-40-1100-30-0001|
|Vibratory bowl (230V 50Hz)||OP-40-1100-30-0007|
|Polishing media (15 Lbs.)||OP-40-1100-30-0002|
|Heavy cleaning media (15 Lbs.)||OP-40-1100-30-0009|
|Optional equipment||Part number|
|Flow-thru rinse system (110V 60Hz)||OP-40-1100-30-0003|
|Flow-thru rinse system (230V 50Hz)||OP-40-1100-30-0008|
|Rinse additive (1 quart)||OP-40-1101-30-0004|
|Rinse additive (1 gallon)||OP-40-1104-30-0005|
|Separating screen kit||OP-40-1100-30-0006|